Abstract: Vietnam is a country with a long coastline and a high population density residing in the coastal plains. The largest dry area in Vietnam, the coastal plain of Ninh Thuan province, always lacks water in the first dry months of the year (Jan., Feb., Mar., and Apr.). Groundwater is an extremely valuable resource for supplies at this time. Therefore, the objective of this study is to establish a comprehensive approach to sustainable groundwater management in this semi-arid region. This approach is not only mitigating the negative impacts of factors such as climate change, sea level rise, and socio-economic development but also suggesting measures for management of aquifer recharge. A groundwater model for a 3-layer system with variable density flow SEAWAT is built to predict the impacts of climate change and sea level rise without a change in groundwater abstraction. This model helps to understand the trend of salt intrusion and lowering groundwater level in the study area. Afterwards, scenarios with different ground water abstraction and groundwater development such as ground dam, infiltration basin have been set up to meet the demands of socio-economic development in the future. Predicted results will show the impacts of the groundwater systems in the area such as groundwater level change, and saltwater intrusion. Controlled groundwater abstraction and some measures of groundwater development such as infiltration basin, underground dam would allow for an increase of up to 50000m3/day in the year 2050 without negative impacts on the aquifer system.

Abstract: In urban environments there is a severe reduction of infiltration and groundwater recharge due to the existence of large impervious areas. During rain events, large volumes of water that could have recharged groundwater and surface water bodies are diverted into the municipal drainage system and lost from the freshwater storage. Moreover, extreme rain events impose high peak flows and large runoff volumes, which increase the risk of urban floods. Recent studies have suggested the use of rainwater harvesting for groundwater recharge, as a plausible solution for these challenges in dense urban environments. While the benefits of this approach are well understood, research on its practical, engineering, and hydrological aspects is relatively limited. The objective of the present study was to examine the use of infiltration wells for groundwater recharge with harvested rainwater collected from building rooftops under Mediterranean climate conditions. Two types of wells with similar hydraulic and technical properties were examined: a well that reaches the groundwater (wet well); and a well that discharges the harvested water into the unsaturated zone (dry well). Infiltration capacities of the wells were compared in controlled experiments conducted during summer months, and in operational recharge of harvested rainwater, during winter. Both dry and wet wells were found to be suitable for purposes of groundwater recharge with rooftop-harvested rainwater. Infiltration capacity of the wet well was about seven times greater than the infiltration capacity of the dry well. While the infiltration capacity of the wet well was constant throughout the entire length of the study (∼10 m3/h/m), the dry well infiltration capacity improved during winter (from 0.5 m3/h/m to 1.5 m3/h/m), a result of development of the dry well with time. Considering Tel-Aviv, Israel, as a case study for a dense modern city in a Mediterranean climate, it is demonstrated herein that the use of infiltration wells may reduce urban drainage by ∼40 %.

Abstract: It is well known that rainwater harvesting (RWH) can augment water supply and reduce stormwater pollutant discharges. Due to the lack of continuous 2D modelling of urban flood coverage and its associated damage, the ability of RWH to reduce urban flood risks has not been fully evaluated. Literature suggests that small distributed storage spaces using RWH tanks will reduce flood damage only during small to medium flooding events and therefore cumulative assessment of their benefits is needed. In this study we developed a new integrated modelling framework that implements a semi-continuous simulation approach to investigate flood prevention and water supply benefits of RWH tanks. The framework includes a continuous mass balance simulation model that considers antecedent rainfall conditions and water demand/usage of tanks and predicts the available storage prior to each storm event. To do so, this model couples a rainfall-runoff tank storage model with a detailed stochastic end-use water demand model. The available storage capacity of tanks is then used as a boundary condition for the novel rapid flood simulation model. This flood model was developed by coupling the U.S. EPA Storm Water Management Model (SWMM) to the Cellular-Automata Fast Flood Evaluation (CA-ffé) model to predict the inundation depth caused by surcharges over the capacity of the drainage network. The stage-depth damage curves method was used to calculate time series of flood damage, which are then directly used for flood risk and cost-benefit analysis. The model was tested through a case study in Melbourne, using a recorded rainfall time series of 85 years (after validating the flood model against 1D-2D MIKE-FLOOD). Results showed that extensive implementation of RWH tanks in the study area is economically feasible and can reduce expected annual damage in the catchment by up to approximately 30 percent. Availability of storage space and temporal distribution of rainfall within an event were important factors affecting tank performance for flood reduction.

Abstract: Combined large-scale rainwater harvesting (RWH) and flood mitigation systems are promising as a sustainable water management strategy in urban areas. These are multi-purpose infrastructure that not only provide a secondary, localised water resource, but can also reduce discharge and hence loads on any downstream wastewater networks if these are integrated into the wider water network. However, the performance of these systems is dependent on the specific design used for its local catchment which can vary significantly between different implementations. A multitude of design strategies exist, however there is no universally accepted standard framework. To tackle these issues, this paper presents a two-player optimisation framework which utilises a stochastic design optimisation model and a competing, high-intensity rainfall design model to optimise passively-operated RWH systems. A customisable tool set is provided, under which optimisation models specific to a given catchment can be built quickly. This reduces the barriers to implementing computationally complex sizing strategies and encouraging more resource-efficient systems to be built. The framework was applied to a densely populated high-rise residential estate, eliminating overflow events from historical rainfall. The optimised configuration resulted in a 32% increase in harvested water yield, but its ability to meet irrigation demands was limited by the operational levels of the treatment pump. Hence, with the inclusion of operational levels in the optimisation model, the framework can provide an efficient large-scale RWH system that is capable of simultaneously meeting water demands and reducing stresses within and beyond its local catchment.

Abstract: Competing commercial demands on water resources need to be balanced as the world’s population rises. Generally, groundwater is raised by subsurface dams. In this paper, the geographic information system (GIS) software and a decision-making method were applied. As the first step, the limitations that affect the establishment of the subsurface dam were identified using eliminating criteria by the Boolean logic. Regarding the second step, the most appropriate axis was determined for subsurface dam construction in each of the limits. The analytical hierarchy process (AHP) was applied according to the evaluation criteria in this study. The aim of using AHP was to weigh and prioritize the criteria of the groundwater dam for recognizing appropriate sites. Among various places and regarding the subsurface dam construction, AHP was conducted using a hierarchy process for finding the most suitable sites in the third stage of the decision-making method. Finally, among the ten appropriate sites, cross comparison was drawn by using Decision Expert (DEX), Evaluation based on Distance from Average Solution (EDAS), and Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS). Compared together (as a process of decision-making), DEX, TOPSIS, and EDAS methods assisted in ranking the most appropriate sites in the final step of subsurface dam pre-selection. A and C axes obtained scores between 1 and 2, among 10 axes according to the numerically ranked locations. Regarding the water shortage issue and better management of the underground water at certain levels, the findings of this study could be useful for the residents of Kajbid-Balaqly Watershed in the dry season. Further, water managers can use the above-mentioned methods for their decisions regarding the proper subsurface dam establishment.