|
|
Borrego-Alonso, D., Quintana-Arnés, B., & Lozano, J. C. (2023). Natural radionuclides behaviour in drinking groundwaters from Castilla y León (Spain); radiological implications. Water Research, 245, 120616.
Abstract: Since the coming into force of the European Council Directive 51/2013 EURATOM and its transposition into the Spanish legislation, the presence of radioactive substances in drinking waters must be kept under surveillance to ensure that the health protection requirements are met. Driven by this regulatory framework, in an attempt to know the starting point from which to design surveillance plans, the groundwaters intended for human consumption of Castilla y León (Spain) have been radiologically characterised by using both low-level γ-ray and α-particle spectrometry to determine the activity concentration of the natural radionuclides needed to account for the indicative dose estimation. This extensive research has comprised the radiological characterisation of more than 400 drinking water samples from one of the European Union’s largest regions. Furthermore, the gross α and gross β activities have been analysed. Results showed a high geographical variability that can be related to the hydrogeological formations where the groundwaters come from. The uranium isotopes, 234U and 238U, are the main radionuclides present in the analysed drinking waters reaching values up to 2000 mBq/L, in the southwestern and western of Castilla y León, where U-rich minerals are part of the host rock. High 210Pb and 226,228Ra occurrences are found in the low permeability igneous and metasedimentary hydrogeological formations of Salamanca province. From a public health protection point of view, 4.4% of the total drinking water samples from intakes exceeded the Indicative Dose parametric value of 0.1 mSv, which is a not negligible number of samples, being very likely related to granitic and metamorphosed host rock under specific local conditions. This fact highlights the need for research and consideration of special surveillance of the groundwaters from these areas.
|
|
|
|
Jamali, B., Bach, P. M., & Deletic, A. (2020). Rainwater harvesting for urban flood management – An integrated modelling framework. Water Research, 171, 115372.
Abstract: It is well known that rainwater harvesting (RWH) can augment water supply and reduce stormwater pollutant discharges. Due to the lack of continuous 2D modelling of urban flood coverage and its associated damage, the ability of RWH to reduce urban flood risks has not been fully evaluated. Literature suggests that small distributed storage spaces using RWH tanks will reduce flood damage only during small to medium flooding events and therefore cumulative assessment of their benefits is needed. In this study we developed a new integrated modelling framework that implements a semi-continuous simulation approach to investigate flood prevention and water supply benefits of RWH tanks. The framework includes a continuous mass balance simulation model that considers antecedent rainfall conditions and water demand/usage of tanks and predicts the available storage prior to each storm event. To do so, this model couples a rainfall-runoff tank storage model with a detailed stochastic end-use water demand model. The available storage capacity of tanks is then used as a boundary condition for the novel rapid flood simulation model. This flood model was developed by coupling the U.S. EPA Storm Water Management Model (SWMM) to the Cellular-Automata Fast Flood Evaluation (CA-ffé) model to predict the inundation depth caused by surcharges over the capacity of the drainage network. The stage-depth damage curves method was used to calculate time series of flood damage, which are then directly used for flood risk and cost-benefit analysis. The model was tested through a case study in Melbourne, using a recorded rainfall time series of 85 years (after validating the flood model against 1D-2D MIKE-FLOOD). Results showed that extensive implementation of RWH tanks in the study area is economically feasible and can reduce expected annual damage in the catchment by up to approximately 30 percent. Availability of storage space and temporal distribution of rainfall within an event were important factors affecting tank performance for flood reduction.
|
|
|
|
Netzer, L., Kurtzman, D., Ben-Hur, M., Livshitz, Y., Katzir, R., & Nachshon, U. (2024). Novel approach to roof rainwater harvesting and aquifer recharge in an urban environment: Dry and wet infiltration wells comparison. Water Research, 252, 121183.
Abstract: In urban environments there is a severe reduction of infiltration and groundwater recharge due to the existence of large impervious areas. During rain events, large volumes of water that could have recharged groundwater and surface water bodies are diverted into the municipal drainage system and lost from the freshwater storage. Moreover, extreme rain events impose high peak flows and large runoff volumes, which increase the risk of urban floods. Recent studies have suggested the use of rainwater harvesting for groundwater recharge, as a plausible solution for these challenges in dense urban environments. While the benefits of this approach are well understood, research on its practical, engineering, and hydrological aspects is relatively limited. The objective of the present study was to examine the use of infiltration wells for groundwater recharge with harvested rainwater collected from building rooftops under Mediterranean climate conditions. Two types of wells with similar hydraulic and technical properties were examined: a well that reaches the groundwater (wet well); and a well that discharges the harvested water into the unsaturated zone (dry well). Infiltration capacities of the wells were compared in controlled experiments conducted during summer months, and in operational recharge of harvested rainwater, during winter. Both dry and wet wells were found to be suitable for purposes of groundwater recharge with rooftop-harvested rainwater. Infiltration capacity of the wet well was about seven times greater than the infiltration capacity of the dry well. While the infiltration capacity of the wet well was constant throughout the entire length of the study (∼10 m3/h/m), the dry well infiltration capacity improved during winter (from 0.5 m3/h/m to 1.5 m3/h/m), a result of development of the dry well with time. Considering Tel-Aviv, Israel, as a case study for a dense modern city in a Mediterranean climate, it is demonstrated herein that the use of infiltration wells may reduce urban drainage by ∼40 %.
|
|
|
|
Soh, Q. Y., O’Dwyer, E., Acha, S., & Shah, N. (2023). Robust optimisation of combined rainwater harvesting and flood mitigation systems. Water Research, 245, 120532.
Abstract: Combined large-scale rainwater harvesting (RWH) and flood mitigation systems are promising as a sustainable water management strategy in urban areas. These are multi-purpose infrastructure that not only provide a secondary, localised water resource, but can also reduce discharge and hence loads on any downstream wastewater networks if these are integrated into the wider water network. However, the performance of these systems is dependent on the specific design used for its local catchment which can vary significantly between different implementations. A multitude of design strategies exist, however there is no universally accepted standard framework. To tackle these issues, this paper presents a two-player optimisation framework which utilises a stochastic design optimisation model and a competing, high-intensity rainfall design model to optimise passively-operated RWH systems. A customisable tool set is provided, under which optimisation models specific to a given catchment can be built quickly. This reduces the barriers to implementing computationally complex sizing strategies and encouraging more resource-efficient systems to be built. The framework was applied to a densely populated high-rise residential estate, eliminating overflow events from historical rainfall. The optimised configuration resulted in a 32% increase in harvested water yield, but its ability to meet irrigation demands was limited by the operational levels of the treatment pump. Hence, with the inclusion of operational levels in the optimisation model, the framework can provide an efficient large-scale RWH system that is capable of simultaneously meeting water demands and reducing stresses within and beyond its local catchment.
|
|
